Schaublin 102 lever collet closer wanted
It's for a W20 reduction geared head and I'm in Australia.:)
View ArticleWeiler Matador Pratt Burnerd kc15 collet chuck
Wondering if anyone has this set up and if these chucks were made for the din55022 spindle? If not what was the solution to fitting one?
View ArticleHembrug lathe
Can someone give me any advice on how to remove the bed rails on my Hembrug lathe . I would like to have them ground . Are new stock rails available ? If so where from ?
View ArticleTOS SV18RA lathe
Hi, I bought a TOS tool room lathe - SV18RA. It's much heavier than most tool room lathes I've seen at about 1.9t (~4000 pounds). I got a longer bed version (1m or 40inches) and it seems like the bulk...
View ArticleSchaublin clone ID-ing
I have a small bench lathe to be restored, looking very similar to a Schaublin 102 and sharing the same main dimensions thereof (102mm centre height, same bed profile, W20 threaded nose, etc.) 'As...
View ArticleSchaublin clone ID-ing
I have a small bench lathe to be restored, looking very similar to a Schaublin 102 and sharing the same main dimensions thereof (102mm centre height, same bed profile, W20 threaded nose, etc.) 'As...
View ArticleClik here to view.
Colchester CHIPMASTER -- making a TAPER ATTACHMENT for.
Here's a bit of background for the 1st 3 pics. To start I used 1 x 3" CRS squared up the ends to 4 inches and milled the top to 15 degrees to mate with the underside of the saddle and help to hold the...
View ArticleClik here to view.
Ikegai A20 High Speed flat belt?
Picked up one today. Missing the flat belt. Anyone know where to get these? Or where to get a made to order flat belt from? Attached Thumbnails Â
View ArticleGraziano Sag12 24vdc clutches.
I'm thinking about using a 24 volt dc power supply to run the clutches. Does anyone know how many amps that the 24 vdc power supply would need to be. Thanks Mike
View ArticleGraziano SAG 12S dials
Hi, Over the last year I have reconditioned and repaired an old Graziano 12S lathe. Part of the recondition was to clean and blacken the dials. They were rusty and you could barely see the numbers. I...
View ArticleClik here to view.
Schaublin 125-CNC retrofit:
Hi Guys, I bought a Schaublin 125-CNC from Richardo (swiss ebay). Seems to have good mechanicals, and have done little work in it's 40 years. I will be modernising it with a new controller. Here is a...
View ArticleSchaublin 120VM
How much does a 120VM typically cost? Good lathe, some chucks and collets, no steadies, no gears. I'm considering one, but I'm not sure on value in uk. It seems in good running order. Clean, original...
View ArticleGraziano SAG 12S cross slide play/wear ...
Hi, In the Graziano SAG 12S that I am working on the cross slide has some play. I found that the part that holds the cross slide half nut has wear in it. I made a new part and that reduced the overall...
View ArticleSmart & Brown Model A MK1
For some time now I have been super interested in high quality tool room lathes.(Monarch 10ee, HLV-H, Schaublin, ect) I really have no need for one but REALLY want one and have been keeping an eye out...
View ArticleLubrication for TOS SUI 40 lathe
Hi guys. I recently got a TOS SUI 40 lathe that has been standing still for quite some time. I have a manual, but it is missing the lubrication chart. Does anyone know what oil, how much, and how to...
View ArticleSwiss Abnox Hand Pump Oilers for Schaublin now on ebay in USA
The hard to find and expensive to ship from Switzerland Abnox hand push pump oilers for lubricating Schaublin lathes are now on ebay: eBay item number: 402728927256 The Seller is an Abnox dealer in the...
View ArticleSupport for mori seiki
Hi everyone, Im in the process of negotiating a used mori seiki lathe but a little concerned about parts and service. Some people told me that since mori became dmg it has become harder to find parts...
View ArticleClik here to view.
Lathe won't start after move
Hello, I've a SAG12 that I recently purchased. I'm new to machining and was lucky to pick up a the lathe for 1k. I tested everything at the buyers shop, it all worked fine no problem. It was plugged...
View ArticleMori Seiki ms1250 electrical diagrams and manual needed
Looking to convert a Mori Seiki MS 1250g to 230 volts. Am hoping someone might be able to assist with electrical diagrams and manuals. Any help will be very much appreciated.
View Article